detector switches/ese58 design and speci? cations are each subject to change without notice. ask factory for the current technical speci? cations before purchase and/or use. should a safety concern arise regarding this product, please be sure to contact us immediately. ? es25 ? 1 e 2 s 3 e 4 5 6 7 8 9 product code design no 8 5 6th l r left-side operation type right-side operation type type 09hl detector switches type: ese58 features thin body: 0.9 mm. circuit type: normally-open and normally-closed types are available. lineup with variations in right-left operations. recommended ap pli ca tions detection of media in portable electronic equipment (mobile phones/digital still cameras/dvcs, etc.) explanation of part numbers speci? cations rating 50 a 3 vdc to 10 ma 5 vdc (resistive load) contact resi stance 500 m max. (initial) insulation resistance 100 m min. (100 vdc) dielectric withstanding vo ltage 100 vac for 1 minute operating force 300 mn max. mounting height 0.9 mm poles and throws 1-pole 1-throw full travel (pus hing distance) with boss : 1.5 mm (1.5 mm) without boss : 1.25 mm (1.5 mm) op er at in g li fe 5 0000 cycles min. temp erature range ?10 c to +60 c heat resistance +70 c for 96 hours low temperature resistance ?25 c for 96 hours humidity resistance +4 0 c 90 % to 95 % rh for 96 hours minimum quantity/packing unit 5000 pcs. embossed taping (reel pack) qu an ti ty /c ar to n3 0000 pcs. oct. 2012 00
detector switches/ese58 design and speci? cations are each subject to change without notice. ask factory for the current technical speci? cations before purchase and/or use. should a safety concern arise regarding this product, please be sure to contact us immediately. ? es26 ? 0.48 r0.14 r2.4 5 0.5 0.2 0.9 0.1 0.39 0.77 0.6 0.05 1.6 0.1 0.4 c0.1 pivot center on position on position operation point full stroke position 2.55 0.2 0.3 4.5 2.8 0.8 0.25 0.7 3.0 3.5 1.6 2.0 1.5 (1) (0.64) 0.24 2.9 pwb mounting hole for reference (pitch tolerance: 0.05) 2? 0.7 0.48 r0.14 r2.45 0.5 0.2 0.9 0.1 0.39 0.77 pivot center on position on position operation point full stroke position 2.3 1.1 1.25 4.5 2.8 0.7 3.0 3.5 1.75 1.25 (0.75) (0.64) 0.24 2.65 pwb mounting hole for reference (pitch tolerance: 0.05) r0.14 r2.4 5 0.5 0.2 pivot center 0.39 0.77 off position 3.0 3.5 0.2 0.6 0.05 1.6 0.1 0.4 0.9 2? 0.7 4.5 2.8 1.6 0.4 0.44 off position operation point 1.5 2.0 full stroke position (1) (0.64) c0. 1 0.3 0.45 0.24 2.9 2.6 0.2 0.9 0.1 pwb mounting hole for reference (pitch tolerance: 0.05) 0.8 0.6 0.45 0.9 r0.14 r2.4 5 0.5 0.2 pivot center 0.39 0.77 off position 3.0 3.5 0.4 0.8 0.6 1.05 1.35 4.5 2.8 0.44 off position operation point 1.05 1.55 full stroke position (0.55) (0.64) 0.3 1.35 0.24 2.45 2.15 0.2 0.9 0.1 pwb mounting hole for reference (pitch tolerance: 0.05) 0.48 r 0.1 4 r2. 4 5 0.5 0.2 0.9 0.1 0.39 0.77 0.6 0.05 1.6 0.1 0.4 c0.1 pivot center on position on position operation point full stroke position 2.55 0.2 0.3 4.5 2.8 0.8 3.5 1.6 2.0 1.5 0.24 2.9 pwb mounting hole for reference (pitch tolerance: 0.05) 2? 0.7 0.25 0.7 3.0 (1) (0.64) 0.48 r 0.1 4 r2. 45 0.5 0.2 0.9 0.1 0.39 0.77 pivot center on position on position operation point full stroke position 2.3 0.2 3.5 1.75 1.25 0.24 2.65 0.7 3.0 (0.75) (0.64) 1.1 1.25 4.5 2.8 pwb mounting hole for reference (pitch tolerance: 0.05) no. 1 with boss ese58l11b nomal closed type ese58l61 j-bent ter mi nals 1-pole 1-throw nomal open type ese58l11 j-bent te rmi nals 1-pole 1-throw nomal open type ese58r11 j-bent terminals 1-pole 1-throw no. 2 with boss ese58l61b no. 3 with boss ese58r11b dimensions in mm (not to scale) without boss ese58l11a without boss ese58l61a without boss ese58r11a oct. 2012 00
detector switches/ese58 design and speci? cations are each subject to change without notice. ask factory for the current technical speci? cations before purchase and/or use. should a safety concern arise regarding this product, please be sure to contact us immediately. ? es27 ? packed portion cover tape carrier tape end top drawing direction pilot holes leading portion 400 mm min. non-packed portion (160 mm min.) non-packed portion (100 mm min.) 16.0 0.3 1.75 0.1 7.5 0.1 1. 5 +0. 1 0 p=8.0 0.1 4.0 0.1 2.0 0.1 13.5 380.0 2.0 16.4 common terminal common terminal c 1 c 1 common terminal common terminal c c 11 0.5 0.2 0.39 0.77 off position 0.6 0.05 1.6 0.1 2? 0.7 4.5 2.8 1.6 0.4 operation point 1.5 2.0 full stroke position c0.1 2.9 2.6 0.2 0.9 0.1 pwb mounting hole for reference (pitch tolerance: 0.05) pivot center r 0.14 r2.45 3.5 0.44 (0.64) 0.24 off position 0.8 0.6 0.45 0.9 3.0 0.45 0.4 0.9 (1) 0.3 0.5 0.2 0.39 0.77 off position operation point 1.05 1.55 full stroke position 2.45 2.15 0.2 0.9 0.1 pwb mounting hole for reference (pitch tolerance: 0.05) 3.0 pivot center r 0.14 r2.45 3.0 3.5 0.4 1.35 0.44 (0.55) (0.64) 0.3 0.24 off position 0.8 0.6 1.05 1.35 4.5 2.8 no. 4 with boss ese58r61b nomal closed type ese58r61 j-bent terminals 1-pole 1-throw dimensions in mm (not to scale) circuit diagram normal open type 1-pole 1-th row (n . o) type ese58l type ese58r normal closed type 1-pole 1-th row (n . c) type ese58l type ese58r packaging speci? cations standard reel dimensions in mm (not to scale) taping reel embossed carrier taping without boss ese58r61a oct. 2012 00
|
